Silicone Soap Mold - Small Oval Guest Size Mold - Crafter's Choice 1608
Silicone Soap Mold - Small Oval Guest Size Mold - Crafter's Choice 1608
Couldn't load pickup availability
DESCRIPTION
DESCRIPTION
Small Oval Guest Silicone Mold - 1608
The small classic soaps made using this mold are perfect for the hospitality industry. Create soaps for hotels and bed & breakfasts with this quality silicone mold.
Common Uses:
Melt & Pour Soap. Cold & Hot Process Soap.
Points of Interest:
Material: Food Grade Silicone
Maximum Product Pour Temp: 500ºF
Makes (9) Individual Bars
Approximate Bar Weight: 2 oz
Measures: 3" x 1.75" x .75"
Mold walls are built with extra thickness to prevent bowing. New glossy finish for a more finished bar appearance!
Available as part of our Guest Size Soap Mold Sample Pack at discounted pricing!
Melt & Pour Soap: Pour melted soap into silicone mold cavities. Allow soap to cool at room temperature until hard. Carefully remove soap from mold by gently pulling the sides away from the soap, and then push on the bottom of the mold until the soap starts to release. Grab hold of the soap and carefully pull out of the mold.
Cold Process Soap: Pour soap at trace into the mold cavities. After at least 24 hours, gently pull silicone mold to loosen its grip on the soap. Flip mold over onto a clean surface and gently push on the bottom of mold until the soap starts to release. Grab hold of the soap with a gloved hand, and allow soap to cure for 4-8 weeks. Note that some cold process soap recipes may require a week to harden enough to remove from the mold. If this is the case with your recipe, we recommend adding sodium lactate to your recipe to assist with creating a harder bar faster.
Cold Process/Oven Process Soap: Pour soap at trace into the mold cavities. Preheat oven to 170ºF then place mold in oven. Turn oven off, and keep soap in oven overnight. The next day remove mold from oven. Carefully remove soap from mold by gently pulling the sides away from the soap, and then push on the bottom of the mold until the soap starts to release. Grab hold of the soap and carefully pull out of the mold. Allow soap to cure for 2 to 4 weeks.
Hot Process Soap: Scoop hot process soap into mold cavities. Gently tap the mold onto the counter to remove air pockets. Allow soap to cool and harden. (This can take up to 48 hours.) Carefully remove soap from mold by gently pulling the sides away from the soap, and then push on the bottom of the mold until the soap starts to release. Grab hold of the soap and carefully pull out of the mold.
Lotion Bars: Pour melted lotion bar mixture into mold cavities. Allow mixture to solidify. Carefully remove lotion bars from mold by gently pulling the sides away from the lotion bars, and then push on the bottom of the mold until the lotion bars starts to release. Grab hold of lotion bar and carefully pull out of mold.
Care:
Hand wash in warm sudsy water.
Once mold is used for making soap, it should not be used for food production. To avoid damage to mold, do not use sharp metal tools to cut or remove contents. Never place near an open flame, use under a broiler, or on a cook top burner.
| California Prop 65 Statement:  | This product is not on the CA Prop 65 list of toxic chemicals. This product conforms to the reporting requirements of California Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1986). We are conforming to the regulation by reporting the existence, or lack thereof, of ingredients deemed reportable by the above mentioned regulations via a Safety Data Sheet (SDS), in Section 15 "Regulatory Information." Ingredients from Natural Food Sources (NFS) and are exempt from reporting in accordance with Title 27, § 25501(a). |
CARE INSTRUCTIONS
CARE INSTRUCTIONS
Wash molds in warm, sudsy water. Do not wash plastic molds in the dishwasher, as it can make them brittle.
Fragrance oils and essential oils, citric acid etc will degrade plastic molds, so it is best to wash out and dry immediately after use. With proper care, you can get 1000+ uses from a single mold.
- Buy More, Save More!
We now offer tiered discounts on select molds! You can mix and match different molds* to receive the discount. Discount is automatic - no coupon required! See table below for details:
