Silicone Soap Mold - Honeycomb Loaf Mold for Soapmaking 1506
Silicone Soap Mold - Honeycomb Loaf Mold for Soapmaking 1506
Couldn't load pickup availability
DESCRIPTION
DESCRIPTION
Honeycomb Silicone Loaf Soap Mold - Crafter's Choice 1506
Create a honeycomb design on the top of your soap bars with this silicone mold! The depth of the honeycomb design is roughly 1/8”. You can save your bubble wrap for packaging the cute honey inspired soaps you’ll create with this mold!
Use with our Honey Melt & Pour Soap Base
Common Uses:
Melt & Pour Soap (MP). Cold Process Soap (CP). Cold Process Oven Process Soap (CPOP). Hot Process Soap (HP).
| Style: Loaf |  |
Bar Depth: 2.5" | |
| Bar Length: 8" | |
Bar Width: 3.5" | |
| Max Temperature: 500ºF | |
Mold Capacity (oz): 44 |
Melt & Pour Soap: Pour melted soap into silicone mold. Allow soap to cool at room temperature until hard. Carefully remove loaf from mold by gently pulling the sides away from the soap, and then push on the bottom of the mold until the soap starts to release. Grab hold of the loaf and carefully pull out of the mold. Slice into bars.
Cold Process Soap: Pour soap at trace into mold. After at least 24 hours, gently pull silicone mold to loosen its grip on the soap. Flip mold over onto a clean surface or cookie sheet and gently push on the bottom of mold until the soap starts to release. Grab hold of the loaf with a gloved hand. Slice into bars and allow soap to cure for 4-8 weeks. Note that some cp soap recipes may require a week to harden enough to remove from the mold. If this is the case with your recipe, we recommend adding sodium lactate to your recipe to assist with creating a harder bar faster.
Cold Process/Oven Process Soap: Pour soap at trace into the mold. Preheat oven to 170ºF then place mold in oven. Turn oven off, and keep soap in oven overnight. The next day remove mold from oven. Carefully remove loaf from mold by gently pulling the sides away from the soap, and then push on the bottom of the mold until the soap starts to release. Grab hold of the soap and carefully pull out of the mold. Slice into bars, and allow soap to cure for 2 to 4 weeks.
Hot Process Soap: Scoop hot process soap into mold. Gently tap the mold onto the counter to remove air pockets. Allow soap to cool and harden. (This can take up to 48 hours.) Carefully remove loaf from mold by gently pulling the sides away from the soap, and then push on the bottom of the mold until the soap starts to release. Grab hold of the loaf and carefully pull out of mold. Slice into bars.
Care:
Hand wash mold in warm, sudsy water.
| California Prop 65 Statement: | This product is not on the CA Prop 65 list of toxic chemicals. This product conforms to the reporting requirements of California Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1986). We are conforming to the regulation by reporting the existence, or lack thereof, of ingredients deemed reportable by the above mentioned regulations via a Safety Data Sheet (SDS), in Section 15 "Regulatory Information." Ingredients from Natural Food Sources (NFS) and are exempt from reporting in accordance with Title 27, § 25501(a). |
CARE INSTRUCTIONS
CARE INSTRUCTIONS
Wash molds in warm, sudsy water. Do not wash plastic molds in the dishwasher, as it can make them brittle.
Fragrance oils and essential oils, citric acid etc will degrade plastic molds, so it is best to wash out and dry immediately after use. With proper care, you can get 1000+ uses from a single mold.
- Buy More, Save More!
We now offer tiered discounts on select molds! You can mix and match different molds* to receive the discount. Discount is automatic - no coupon required! See table below for details:
